camera_controller
This is an old revision of the document!
Camera controller
NOTE: this is a findings dump for now. It is unclear what is what, so there may be stuff pertaining to the h265 codec in here. Not sure how interwoven it is with the camera controller.
Known registers:
| Address | Desc. |
|---|---|
| 0xF0000800 | ??? (might not be strictly camera-related) |
| 0xF000081C | ??? address for some buffer |
| 0xF0000820 | ??? set to 0x400000 |
| 0xF0000828 | ??? set to same as F000081C |
| 0xF000082C | ??? set to 0x400000 |
| 0xF0008414 | ??? |
| 0xF0008420 | ??? |
| 0xF0008460 | ??? buffer? position? |
| 0xF0008468 | IRQ status/ack for IRQ 0x11 |
| 0xF000846C | ??? buffer? position? |
| 0xF0008470 | ??? buffer? position? |
| 0xF0008474 | ??? buffer? position? |
| 0xF0008478 | ??? IRQ enable flags?? |
| 0xF00084A4 | buffer address for incoming h265 data? |
| 0xF00084A8 | another buffer address? |
| 0xF00084AC | ??? buffer? position? |
| 0xF00084B0 | IRQ status/ack for IRQ 0x12 |
| 0xF00084B8 | ??? |
| 0xF0008800 | ??? |
| 0xF0008810 | ??? control reg? |
| 0xF0008814 | ??? |
| 0xF000881C+(N*8) | table N, bytes 0..3 (N=0..7) |
| 0xF0008820+(N*8) | table N, byte 4 |
| 0xF000886C | ??? |
| 0xF000887C+(N*8) | table N, bytes 0..3 (N=0..7) |
| 0xF0008880+(N*8) | table N, byte 4 |
| 0xF00088B4 | ??? (related to framerate?) (actually part of the tables above) |
| 0xF0008C00 | ??? |
| 0xF0008C04 | ??? weird value, timings? |
| 0xF0008C08 | Resolution? |
| 0xF0008C10 | ??? |
| 0xF0008C28 | ??? |
| 0xF0008C2C | ??? |
| 0xF0008C34 | ??? |
| 0xF0008C70 | IRQ status/ack for IRQ 0x10 |
| 0xF0008C74 | ??? related to IRQ 0x10? |
| 0xF0009000 | ??? control register? |
| 0xF0009004 | ??? vertical resolution? |
| 0xF0009008 | ??? |
| 0xF0009028 | IRQ disable/status/ack for IRQ 0x14 |
| 0xF0009030 | ??? (IRQ position?? think F0009508) |
| 0xF0009034 | ??? (IRQ position??) |
| 0xF0009038 | IRQ status/ack for IRQ 0x1D |
| 0xF0009040 | extra IRQ status/ack for IRQ 0x14 |
| 0xF0009044 | ??? |
Related IRQs:
| IRQ | Desc. |
|---|---|
| 0x10 | ??? |
| 0x11 | data ready? |
| 0x14 | ??? |
| 0x1D | ??? |
0xF0009028
IRQ disable, status and acknowledge, condensed into one register.
Bits 0-7 are the status flags. Bits 8-15 are the disable flags (ie. setting a bit to 1 disables the corresponding IRQ). Bits 16-23 are the acknowledge flags, ie. writing a 1 to a bit acknowledges the corresponding IRQ.
| IRQ bit | Desc. |
|---|---|
| 0 | Vertical IRQ |
| 1 | ??? |
| 2 | ??? |
| 3 | ??? |
| 4 | ??? |
| 5 | ??? |
| 6 | ??? |
| 7 | ??? |
IRQ 1, 2 and 5 are unused by the stock firmware.
IRQ 0 fires at the position specified by register 0xF00094F8 plus 8 scanlines.
These IRQ conditions are connected to IRQ 0x14.
camera_controller.1744849007.txt.gz · Last modified: 2025/04/17 00:16 by arisotura